When ordering 8T-650-01 mud pump parts, start with the component drawing reference and the actual pump configuration. The two supplied Russian documents concern the same model, written 8Т-650-01; the letters РЭ identify the operating-manual document, not an additional pump model.
The catalogue separates the hydraulic block, piston assembly, power-end shafts and pressure-dampening equipment. Naming the assembly first helps distinguish a complete unit from an individual seal, valve or shaft component.
Specification and identification points
| Parameter / identification item | Documented value | Source / PDF page |
|---|---|---|
| Pump type | Horizontal, three-piston, single-acting | 8TM / 6 |
| Drive-shaft power stated in the manual | 475 kW (650 hp) | 8TM / 6 |
| Maximum piston stroke rate | 160 per minute | 8TM / 6 |
| Maximum drive-shaft speed | 695 rpm | 8TM / 6 |
| Gear ratio | 4.34 | 8TM / 6 |
| Liner / piston diameter options listed | 100, 110, 125, 140, 150, 160, 170, 180 and 190 mm | 8TM / 6 |
| Flow condition stated in the manual | 45 L/s at 190 mm piston diameter and 160 per minute; the stated test condition includes 1000 kg/m³ fluid and 475 kW; not simultaneous with the maximum-pressure condition | 8TM / 6 |
| Discharge-pressure condition stated in the manual | 32 MPa at 100 mm piston diameter and 160 per minute; the stated test condition includes 1000 kg/m³ fluid and 475 kW; not simultaneous with maximum flow | 8TM / 6 |
| Stroke value in the parts catalogue | 203 mm; differs from the supplied operating manual; resolve for the actual pump before selecting parts | 8TC / 2 |
| Stroke value in the 2003 operating manual | 205 ± 0.5 mm; do not silently substitute this for the catalogue's 203 mm | 8TM / 6 |
Check the edition before using a dimension
The supplied parts catalogue prints a 203 mm piston stroke, while the 2003 operating manual prints 205 ± 0.5 mm. This guide preserves both source values instead of choosing one without evidence. Confirm the installed pump and its original drawing before ordering stroke-dependent components.
The manual also gives different conditions for the 45 L/s flow figure and the 32 MPa discharge-pressure figure. They use different piston diameters. These figures must not be combined into a single simultaneous operating point.
Match the scope of the replacement
For a piston-related order, provide the installed liner diameter, piston construction, rod interface and flushing arrangement. For a hydraulic-block enquiry, include valve-cover, manifold and mounting photographs. Shaft replacements require mating dimensions, key details and the exact suffix on the drawing.
The following is a selected reference table checked against the source pages. It is not the complete pump bill of materials. A pump model or a document number is not a substitute for the component drawing reference.
Retain the original characters in a reference, including the Cyrillic letters СБ where shown. Similar-looking Latin letters or an omitted suffix can make a quotation ambiguous. The references identify entries in these catalogues; they do not prove that a replacement from a different edition will fit.
Information to include in a parts enquiry
- Complete pump designation, manufacturer shown on the nameplate, serial number and year.
- Original drawing or catalogue reference, including every suffix and the figure / position number.
- Part photographs, key mating dimensions and the assembly in which the part is installed.
- For fluid-end consumables: liner bore, piston construction, seal arrangement and required quantity.
- Delivery destination and the list of parts required for the same maintenance job.
For an 8T-650-01 enquiry, send the reference together with the pump details for identification. See our mud pump spare parts enquiry page or oilfield equipment parts catalogue. Availability and suitability require confirmation for the actual configuration.
Document references
- 8TC: 8T-650-01 parts and assembly catalogue, 413-000-000 КДС. Page numbers in the tables identify the PDF file page, counted from 1.
- 8TM: 8T-650-01 operating manual, 2003, 8Т-650-01 РЭ. Page numbers in the tables identify the PDF file page, counted from 1.
These references describe the supplied documents. They do not establish present inventory, original-manufacturer authorisation or interchangeability with another pump revision.
8T source-specific liner, piston and seal variants
The catalogue and operating manual give different seal-to-liner assignments. Keep each source version separate. A short suffix such as -01 is shown as printed; it is not presented as an independently confirmed complete part number. A blank source cell is shown as an em dash and does not automatically inherit the preceding code.
Table 2, piston-assembly seals
S1, PDF p. 25
| Reference as printed | Size / source context |
|---|---|
8Т310.100.115-04 | liner D100–160 mm |
-06 | liner D170–190 mm |
Table 3, metric cylinder liners
S1, PDF p. 25
| Reference as printed | Size / source context |
|---|---|
412-126-002 | D100 mm |
-01 | D110 mm |
-02 | D125 mm |
-03 | D140 mm |
-04 | D150 mm |
-05 | D160 mm |
-06 | D170 mm |
-07 | D180 mm |
-08 | D190 mm |
Table 4, metric piston assemblies
S1, PDF p. 25
| Reference as printed | Size / source context |
|---|---|
412-126-100 | D190 mm |
-01 | D180 mm |
-02 | D170 mm |
412-126-200 | D160 mm |
-01 | D150 mm |
-02 | D140 mm |
412-126-300 | D125 mm |
-01 | D110 mm |
-02 | D100 mm |
Table 3, imperial cylinder-liner order designations
S1, PDF p. 25
| Reference as printed | Size / source context |
|---|---|
8Т650-01 4" | 101.6 mm |
8Т650-01 4 ½" | 114.3 mm |
8Т650-01 5" | 127 mm |
8Т650-01 5 ½" | 139.7 mm |
8Т650-01 6" | 152.4 mm |
8Т650-01 6 ½" | 165.1 mm |
Table A.1, cylinder liners
S2, PDF p. 57
| Reference as printed | Size / source context |
|---|---|
412-126-002 | D100 mm |
-01 | D110 mm |
-02 | D125 mm |
-03 | D140 mm |
-04 | D150 mm |
-05 | D160 mm |
-06 | D170 mm |
-07 | D180 mm |
-08 | D190 mm |
Table A.2, piston assemblies
S2, PDF p. 57
| Reference as printed | Size / source context |
|---|---|
412-126-100 | D190 mm |
-01 | D180 mm |
-02 | D170 mm |
412-126-200 | D160 mm |
-01 | D150 mm |
-02 | D140 mm |
412-126-300 | D125 mm |
-01 | D110 mm |
-02 | D100 mm |
Figure A.22 liner variants
S2, PDF p. 74
| Reference as printed | Size / source context |
|---|---|
412-126-002 | D100 mm |
-01 | D110 mm |
-02 | D125 mm |
-03 | D140 mm |
-04 | D150 mm |
-05 | D160 mm |
-06 | D170 mm |
-07 | D180 mm |
-08 | D190 mm |
Figure A.23 piston cores
S2, PDF p. 75
| Reference as printed | Size / source context |
|---|---|
414-123-302-ВМ | D100 mm |
-01 | D110 mm |
-02 | D125 mm |
Figure A.24 piston cores
S2, PDF p. 76
| Reference as printed | Size / source context |
|---|---|
414-123-111ВМ | D150 mm |
414-123-111ВМ-01 | D160 mm |
414-123-111ВМ-02 | D170 mm |
414-123-111ВМ-03 | D180 mm |
414-123-111ВМ-04 | D190 mm |
-05 | D140 mm |
Figure A.25 piston-cup variants
S2, PDF p. 77
| Reference as printed | Size / source context |
|---|---|
412-126-110 | D189.8 mm |
-01 | D179.8 mm |
-02 | D169.8 mm |
Figure A.26 piston-cup variants
S2, PDF p. 78
| Reference as printed | Size / source context |
|---|---|
412-126-210 | D159.8 mm |
-01 | D149.8 mm |
-02 | D139.8 mm |
Figure A.27 piston-cup variants
S2, PDF p. 79
| Reference as printed | Size / source context |
|---|---|
412-126-310 | D124.8 mm |
-01 | D109.8 mm |
-02 | D99.8 mm |
Figure A.30 seal variants
S2, PDF p. 82
| Reference as printed | Size / source context |
|---|---|
8Т310.100.115 | D89 ±1 mm |
-01 | D99 ±1 mm |
-02 | D132 ±1 mm |
-03 | D159 ±1 mm |
-04 | D193 ±1 mm |
-05 | D239 ±1 mm |
8T-650-01 part and drawing references
This selected list contains 262 checked reference entries. It is not a complete bill of materials. Keep the exact number, source edition and installed configuration together when requesting a quotation.
262 reference entries
| Part / drawing number | Component | Configuration / reference scope | Source / PDF page |
|---|---|---|---|
412-113-001-Д | Crankshaft | Selected catalogue reference; check the installed configuration. | S1, PDF p. 5 |
412-112-001-Д | Drive shaft | Selected catalogue reference; check the installed configuration. | S1, PDF p. 5 |
412-114-001-Е-01 | Crosshead | Selected catalogue reference; check the installed configuration. | S1, PDF p. 5 |
412-114-130 ВМ | Stuffing-box chamber | Selected catalogue reference; check the installed configuration. | S1, PDF p. 5 |
412-118-000 | Lubrication system | Selected catalogue reference; check the installed configuration. | S1, PDF p. 5 |
412-125-000 | Hydraulic block | Selected catalogue reference; check the installed configuration. | S1, PDF p. 5 |
412-126-000 | Piston assembly | Selected catalogue reference; check the installed configuration. | S1, PDF p. 5 |
412-127-000 | Piston-assembly flushing system | Selected catalogue reference; check the installed configuration. | S1, PDF p. 5 |
8Т650ВМ.600.000 | High-pressure pulsation dampener | Selected catalogue reference; check the installed configuration. | S1, PDF p. 5 |
8Т650ВМ.700.000 | Low-pressure pulsation dampener | Selected catalogue reference; check the installed configuration. | S1, PDF p. 5 |
8Т650ВМ.400.000-01 | Safety valve | Selected catalogue reference; check the installed configuration. | S1, PDF p. 5 |
412-113-001-Д | Crankshaft | Prior individually reviewed source/model scope; source catalogue part or assembly identifier | S1, PDF p. 5 |
412-112-001-Д | Drive shaft | Prior individually reviewed source/model scope; source catalogue part or assembly identifier | S1, PDF p. 5 |
412-114-001-Е-01 | Crosshead | Prior individually reviewed source/model scope; source catalogue part or assembly identifier | S1, PDF p. 5 |
412-114-130 ВМ | Stuffing-box chamber | Prior individually reviewed source/model scope; source catalogue part or assembly identifier | S1, PDF p. 5 |
412-118-000 | Lubrication system | Prior individually reviewed source/model scope; source catalogue part or assembly identifier | S1, PDF p. 5 |
412-125-000 | Hydraulic block | Prior individually reviewed source/model scope; source catalogue part or assembly identifier | S1, PDF p. 5 |
412-126-000 | Piston assembly | Prior individually reviewed source/model scope; source catalogue part or assembly identifier | S1, PDF p. 5 |
412-127-000 | Piston-assembly flushing system | Prior individually reviewed source/model scope; source catalogue part or assembly identifier | S1, PDF p. 5 |
8Т650ВМ.600.000 | High-pressure pulsation dampener | Prior individually reviewed source/model scope; source catalogue part or assembly identifier | S1, PDF p. 5 |
8Т650ВМ.700.000 | Low-pressure pulsation dampener | Prior individually reviewed source/model scope; source catalogue part or assembly identifier | S1, PDF p. 5 |
8Т650ВМ.400.000-01 | Safety valve | Prior individually reviewed source/model scope; source catalogue part or assembly identifier | S1, PDF p. 5 |
412-113-001-Д | Crankshaft assembly | Catalogue main assembly index, source model 8Т-650-01; source catalogue part or assembly drawing identifier | S1, PDF p. 5 |
412-112-001-Д | Drive shaft assembly | Catalogue main assembly index, source model 8Т-650-01; source catalogue part or assembly drawing identifier | S1, PDF p. 5 |
412-114-001-Е-01 | Crosshead assembly | Catalogue main assembly index, source model 8Т-650-01; source catalogue part or assembly drawing identifier | S1, PDF p. 5 |
412-114-130 ВМ | Seal chamber | Catalogue main assembly index, source model 8Т-650-01; source catalogue part or assembly drawing identifier | S1, PDF p. 5 |
412-118-000 | Lubrication system | Catalogue main assembly index, source model 8Т-650-01; source catalogue part or assembly drawing identifier | S1, PDF p. 5 |
412-125-000 | Fluid end | Catalogue main assembly index, source model 8Т-650-01; source catalogue part or assembly drawing identifier | S1, PDF p. 5 |
412-126-000 | Piston assembly | Catalogue main assembly index, source model 8Т-650-01; source catalogue part or assembly drawing identifier | S1, PDF p. 5 |
412-127-000 | Piston-wash system | Catalogue main assembly index, source model 8Т-650-01; source catalogue part or assembly drawing identifier | S1, PDF p. 5 |
8Т650ВМ.600.000 | Low-pressure pulsation dampener | Catalogue main assembly index, source model 8Т-650-01; source catalogue part or assembly drawing identifier | S1, PDF p. 5 |
8Т650ВМ.700.000 | High-pressure pulsation dampener | Catalogue main assembly index, source model 8Т-650-01; source catalogue part or assembly drawing identifier | S1, PDF p. 5 |
8Т650ВМ.400.000-01 | Safety valve | Catalogue main assembly index, source model 8Т-650-01; source catalogue part or assembly drawing identifier | S1, PDF p. 5 |
412-113-002-Е-02 | Crankshaft | Crankshaft assembly 412-113-001-Д; catalogue Figure 1 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 6 |
412-113-030 | Connecting rod | Crankshaft assembly 412-113-001-Д; catalogue Figure 1 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 6 |
412-113-004-С | Left bearing housing | Crankshaft assembly 412-113-001-Д; catalogue Figure 1 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 6 |
412-113-005-С | Right bearing housing | Crankshaft assembly 412-113-001-Д; catalogue Figure 1 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 6 |
412-113-006-С | Half ring | Crankshaft assembly 412-113-001-Д; catalogue Figure 1 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 6 |
412-113-007-С-01 | Ring | Crankshaft assembly 412-113-001-Д; catalogue Figure 1 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 6 |
412-113-008-В | Retaining ring | Crankshaft assembly 412-113-001-Д; catalogue Figure 1 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 6 |
412-113-009-В | Disc | Crankshaft assembly 412-113-001-Д; catalogue Figure 1 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 6 |
412-113-010-В | Retaining ring | Crankshaft assembly 412-113-001-Д; catalogue Figure 1 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 6 |
412-113-011-В | Gasket | Crankshaft assembly 412-113-001-Д; catalogue Figure 1 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 6 |
412-113-012-ВМ | Pipe plug | Crankshaft assembly 412-113-001-Д; catalogue Figure 1 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 6 |
412-113-050-ВМ | Cover | Crankshaft assembly 412-113-001-Д; catalogue Figure 1 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 6 |
412-113-014-С | Oil pickup | Crankshaft assembly 412-113-001-Д; catalogue Figure 1 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 6 |
412-113-015-С | Lubrication pocket | Crankshaft assembly 412-113-001-Д; catalogue Figure 1 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 6 |
412-113-022-С | Right oil collector | Crankshaft assembly 412-113-001-Д; catalogue Figure 1 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 6 |
412-113-023-В | Bolt, S=50 | Crankshaft assembly 412-113-001-Д; catalogue Figure 1 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 6 |
412-113-025-ВМ | Castellated nut, S=50 | Crankshaft assembly 412-113-001-Д; catalogue Figure 1 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 6 |
412-113-024-В | Bolt, S=24 | Crankshaft assembly 412-113-001-Д; catalogue Figure 1 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 6 |
412-113-101-ВМ | Gear wheel | Crankshaft assembly 412-113-001-Д; catalogue Figure 1 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 6 |
412-113-002 | Crankshaft | Crankshaft assembly 412-113-001-Д; catalogue Figure 1 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 6 |
412-113-007-С-02 | Ring | Crankshaft assembly 412-113-001-Д; catalogue Figure 1 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 6 |
412-112-101-ВМ-01 | Drive shaft | Drive shaft assembly 412-112-001-Д; catalogue Figure 2 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 8 |
412-112-002 | Bearing cup | Drive shaft assembly 412-112-001-Д; catalogue Figure 2 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 8 |
412-112-003-С | Bushing | Drive shaft assembly 412-112-001-Д; catalogue Figure 2 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 8 |
412-112-004-С | Flange | Drive shaft assembly 412-112-001-Д; catalogue Figure 2 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 8 |
412-112-005-С | Cap | Drive shaft assembly 412-112-001-Д; catalogue Figure 2 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 8 |
412-112-006-В | Gasket | Drive shaft assembly 412-112-001-Д; catalogue Figure 2 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 8 |
412-112-007-В | Gasket | Drive shaft assembly 412-112-001-Д; catalogue Figure 2 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 8 |
412-112-008 | Wall plate | Drive shaft assembly 412-112-001-Д; catalogue Figure 2 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 8 |
412-114-002-D | Crosshead | Crosshead assembly 412-114-001-Е-01; catalogue Figure 3 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 9 |
412-114-003-С | Upper guide | Crosshead assembly 412-114-001-Е-01; catalogue Figure 3 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 9 |
412-114-004-С | Lower guide | Crosshead assembly 412-114-001-Е-01; catalogue Figure 3 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 9 |
412-114-005-С-01 | Connecting-rod pin | Crosshead assembly 412-114-001-Е-01; catalogue Figure 3 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 9 |
412-114-006-С | Oil collector | Crosshead assembly 412-114-001-Е-01; catalogue Figure 3 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 9 |
414-114-007-В | Screw | Crosshead assembly 412-114-001-Е-01; catalogue Figure 3 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 9 |
414-114-008-В | Plate nut | Crosshead assembly 412-114-001-Е-01; catalogue Figure 3 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 9 |
412-114-012 | Rod | Crosshead assembly 412-114-001-Е-01; catalogue Figure 3 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 9 |
412-414-013 | Bearing insert | Crosshead assembly 412-114-001-Е-01; catalogue Figure 3 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 9 |
412-114-140-ВМ | Seal-chamber housing | Seal chamber 412-114-130 ВМ; catalogue Figure 4 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 13 |
412-114-107 | Sealing cup | Seal chamber 412-114-130 ВМ; catalogue Figure 4 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 13 |
412-114-121 | Gasket | Seal chamber 412-114-130 ВМ; catalogue Figure 4 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 13 |
412-114-133-ВМ | Ring | Seal chamber 412-114-130 ВМ; catalogue Figure 4 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 13 |
412-114-134-ВМ | Cover | Seal chamber 412-114-130 ВМ; catalogue Figure 4 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 13 |
414-114-120-В | Gasket | Seal chamber 412-114-130 ВМ; catalogue Figure 4 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 13 |
412-116-100-ВМ | Oil trough | Lubrication system 412-118-000; catalogue Figure 5 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 14 |
412-116-300-ВМ | Manifold | Lubrication system 412-118-000; catalogue Figure 5 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 14 |
412-116-400-ВМ | Pump assembly | Lubrication system 412-118-000; catalogue Figure 5 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 14 |
412-116-500-ВМ | Straight connection | Lubrication system 412-118-000; catalogue Figure 5 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 14 |
412-116-600-ВМ | Angled connection | Lubrication system 412-118-000; catalogue Figure 5 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 14 |
412-118-060 | Tee | Lubrication system 412-118-000; catalogue Figure 5 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 14 |
412-118-070 | Flange | Lubrication system 412-118-000; catalogue Figure 5 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 14 |
412-116-900-ВМ | Tee | Lubrication system 412-118-000; catalogue Figure 5 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 14 |
412-118-100 | Filter | Lubrication system 412-118-000; catalogue Figure 5 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 14 |
8Т310.130.020 | Bypass valve | Lubrication system 412-118-000; catalogue Figure 5 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 14 |
412-118-020 | Support post | Lubrication system 412-118-000; catalogue Figure 5 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 14 |
8Т310.130.113 | Gasket | Lubrication system 412-118-000; catalogue Figure 5 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 14 |
412-118-071-01 | Flange | Lubrication system 412-118-000; catalogue Figure 5 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 14 |
412-116-002-ВМ | Elbow | Lubrication system 412-118-000; catalogue Figure 5 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 14 |
412-116-003-ВМ | Tube | Lubrication system 412-118-000; catalogue Figure 5 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 14 |
412-116-004-ВМ | Pipe nipple | Lubrication system 412-118-000; catalogue Figure 5 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 14 |
412-116-004-ВМ-01 | Pipe nipple | Lubrication system 412-118-000; catalogue Figure 5 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 14 |
412-116-005-ВМ | Pipe nipple | Lubrication system 412-118-000; catalogue Figure 5 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 14 |
412-116-005-ВМ-01 | Pipe nipple | Lubrication system 412-118-000; catalogue Figure 5 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 14 |
412-116-005-ВМ-02 | Pipe nipple | Lubrication system 412-118-000; catalogue Figure 5 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 14 |
412-116-006-ВМ | Elbow | Lubrication system 412-118-000; catalogue Figure 5 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 14 |
412-116-007-ВМ | Tube | Lubrication system 412-118-000; catalogue Figure 5 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 14 |
412-116-011-ВМ | Jet | Lubrication system 412-118-000; catalogue Figure 5 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 14 |
412-116-015-ВМ-02 | Gasket | Lubrication system 412-118-000; catalogue Figure 5 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 14 |
412-116-015-ВМ-03 | Gasket | Lubrication system 412-118-000; catalogue Figure 5 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 14 |
412-116-201-ВМ | Nut | Lubrication system 412-118-000; catalogue Figure 5 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 14 |
412-116-502-ВМ | Nut | Lubrication system 412-118-000; catalogue Figure 5 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 14 |
412-116-503-ВМ | Nipple | Lubrication system 412-118-000; catalogue Figure 5 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 14 |
412-118-018 | Gasket | Lubrication system 412-118-000; catalogue Figure 5 / BOM continuation; source catalogue part or assembly drawing identifier | S1, PDF p. 15 |
412-118-007 | Connector | Lubrication system 412-118-000; catalogue Figure 5 / BOM continuation; source catalogue part or assembly drawing identifier | S1, PDF p. 15 |
412-118-008 | Nipple | Lubrication system 412-118-000; catalogue Figure 5 / BOM continuation; source catalogue part or assembly drawing identifier | S1, PDF p. 15 |
412-118-009 | Bolt | Lubrication system 412-118-000; catalogue Figure 5 / BOM continuation; source catalogue part or assembly drawing identifier | S1, PDF p. 15 |
412-118-014 | Guard | Lubrication system 412-118-000; catalogue Figure 5 / BOM continuation; source catalogue part or assembly drawing identifier | S1, PDF p. 15 |
412-118-015 | Angle bracket | Lubrication system 412-118-000; catalogue Figure 5 / BOM continuation; source catalogue part or assembly drawing identifier | S1, PDF p. 15 |
412-118-006 | Adapter | Lubrication system 412-118-000; catalogue Figure 5 / BOM continuation; source catalogue part or assembly drawing identifier | S1, PDF p. 15 |
413-118-023 | Tee | Lubrication system 412-118-000; catalogue Figure 5 / BOM continuation; source catalogue part or assembly drawing identifier | S1, PDF p. 15 |
412-118-024 | Connector | Lubrication system 412-118-000; catalogue Figure 5 / BOM continuation; source catalogue part or assembly drawing identifier | S1, PDF p. 15 |
412-118-025 | Indicator | Lubrication system 412-118-000; catalogue Figure 5 / BOM continuation; source catalogue part or assembly drawing identifier | S1, PDF p. 15 |
412-118-026 | Gasket | Lubrication system 412-118-000; catalogue Figure 5 / BOM continuation; source catalogue part or assembly drawing identifier | S1, PDF p. 15 |
412-124-002-С | Suction manifold assembly | Fluid end 412-125-000; catalogue Figure 6 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 19 |
412-124-010 | Discharge unit assembly | Fluid end 412-125-000; catalogue Figure 6 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 19 |
414-120-009-С | Cover lock | Fluid end 412-125-000; catalogue Figure 6 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 19 |
414-120-013-С | Valve guide | Fluid end 412-125-000; catalogue Figure 6 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 19 |
414-122-201-Т-ВМ | Valve | Fluid end 412-125-000; catalogue Figure 6 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 19 |
8Т650ВМ.600.000 | Low-pressure pulsation dampener | Fluid end 412-125-000; catalogue Figure 6 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 19 |
8Т650ВМ.700.000 | PK40/320 pulsation dampener | Fluid end 412-125-000; catalogue Figure 6 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 19 |
412-125-010 | Plug | Fluid end 412-125-000; catalogue Figure 6 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 19 |
412-117-002-В/6-ВМ-01 | Gasket | Fluid end 412-125-000; catalogue Figure 6 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 19 |
412-120-001-Е/1 | Nut | Fluid end 412-125-000; catalogue Figure 6 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 19 |
412-120-001-Е/2 | Nut | Fluid end 412-125-000; catalogue Figure 6 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 19 |
412-120-001-Е/3-ВМ-01 | Flange | Fluid end 412-125-000; catalogue Figure 6 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 19 |
412-120-001-Е/3-ВМ-02 | Flange | Fluid end 412-125-000; catalogue Figure 6 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 19 |
412-120-001-Е/5-ВМ | Nipple | Fluid end 412-125-000; catalogue Figure 6 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 19 |
412-120-001-Е/6-ВМ | Nut | Fluid end 412-125-000; catalogue Figure 6 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 19 |
412-120-001-Е/7-ВМ | Pipe nipple | Fluid end 412-125-000; catalogue Figure 6 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 19 |
412-120-001-Е/8-ВМ | Plug | Fluid end 412-125-000; catalogue Figure 6 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 19 |
412-120-010-С | Threaded ring | Fluid end 412-125-000; catalogue Figure 6 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 19 |
412-120-011-С | Outer coupling | Fluid end 412-125-000; catalogue Figure 6 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 19 |
412-120-012-С | Inner coupling | Fluid end 412-125-000; catalogue Figure 6 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 19 |
412-120-025 | Support ring | Fluid end 412-125-000; catalogue Figure 6 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 19 |
412-120-026 | Thrust ring | Fluid end 412-125-000; catalogue Figure 6 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 19 |
412-124-010-ВМ/3 | Ring | Fluid end 412-125-000; catalogue Figure 6 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 19 |
414-120-006-В | Stud | Fluid end 412-125-000; catalogue Figure 6 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 19 |
414-120-015-В-ВМ | Valve guide | Fluid end 412-125-000; catalogue Figure 6 / BOM continuation; source catalogue part or assembly drawing identifier | S1, PDF p. 20 |
414-120-020-В | Stud | Fluid end 412-125-000; catalogue Figure 6 / BOM continuation; source catalogue part or assembly drawing identifier | S1, PDF p. 20 |
414-122-101-Т-ВМ | Spring | Fluid end 412-125-000; catalogue Figure 6 / BOM continuation; source catalogue part or assembly drawing identifier | S1, PDF p. 20 |
414-122-301-Т-ВМ | Valve seat | Fluid end 412-125-000; catalogue Figure 6 / BOM continuation; source catalogue part or assembly drawing identifier | S1, PDF p. 20 |
414-123-033 | Wear plate | Fluid end 412-125-000; catalogue Figure 6 / BOM continuation; source catalogue part or assembly drawing identifier | S1, PDF p. 20 |
414-123-002-N-ВМ | Seal | Fluid end 412-125-000; catalogue Figure 6 / BOM continuation; source catalogue part or assembly drawing identifier | S1, PDF p. 20 |
8Т310.100.115-04 | Seal | Fluid end 412-125-000; catalogue Figure 6 / BOM continuation; source catalogue part or assembly drawing identifier | S1, PDF p. 20 |
414-124-001 | Adapter | Fluid end 412-125-000; catalogue Figure 6 / BOM continuation; source catalogue part or assembly drawing identifier | S1, PDF p. 20 |
414-124-004-В | Gasket | Fluid end 412-125-000; catalogue Figure 6 / BOM continuation; source catalogue part or assembly drawing identifier | S1, PDF p. 20 |
414-124-005-В | Gasket | Fluid end 412-125-000; catalogue Figure 6 / BOM continuation; source catalogue part or assembly drawing identifier | S1, PDF p. 20 |
414-124-009-В | Flange plug | Fluid end 412-125-000; catalogue Figure 6 / BOM continuation; source catalogue part or assembly drawing identifier | S1, PDF p. 20 |
8Т650ВМ.020.001 | Adapter | Fluid end 412-125-000; catalogue Figure 6 / BOM continuation; source catalogue part or assembly drawing identifier | S1, PDF p. 20 |
412-125-001 | Fluid-end body | Fluid end 412-125-000; catalogue Figure 6 / BOM continuation; source catalogue part or assembly drawing identifier | S1, PDF p. 20 |
412-125-006 | Valve-guide holder | Fluid end 412-125-000; catalogue Figure 6 / BOM continuation; source catalogue part or assembly drawing identifier | S1, PDF p. 20 |
412-125-007 | Plug | Fluid end 412-125-000; catalogue Figure 6 / BOM continuation; source catalogue part or assembly drawing identifier | S1, PDF p. 20 |
412-125-008 | Stud | Fluid end 412-125-000; catalogue Figure 6 / BOM continuation; source catalogue part or assembly drawing identifier | S1, PDF p. 20 |
412-125-008-01 | Stud | Fluid end 412-125-000; catalogue Figure 6 / BOM continuation; source catalogue part or assembly drawing identifier | S1, PDF p. 20 |
412-125-008-02 | Stud | Fluid end 412-125-000; catalogue Figure 6 / BOM continuation; source catalogue part or assembly drawing identifier | S1, PDF p. 20 |
412-125-009 | Protective ring | Fluid end 412-125-000; catalogue Figure 6 / BOM continuation; source catalogue part or assembly drawing identifier | S1, PDF p. 20 |
414-123-003 В | Wear plate | Piston assembly 412-126-000; catalogue piston/liner/seal tables; source version only; 2; source catalogue part or assembly drawing identifier | S1, PDF p. 25 |
414-123-004 В | Reflector baffle | Piston assembly 412-126-000; catalogue piston/liner/seal tables; source version only; 3; source catalogue part or assembly drawing identifier | S1, PDF p. 25 |
414-123-005 В | Reflector plate | Piston assembly 412-126-000; catalogue piston/liner/seal tables; source version only; 4; source catalogue part or assembly drawing identifier | S1, PDF p. 25 |
414-123-006 В | Locknut | Piston assembly 412-126-000; catalogue piston/liner/seal tables; source version only; 5; source catalogue part or assembly drawing identifier | S1, PDF p. 25 |
414-126-011 | Piston rod | Piston assembly 412-126-000; catalogue piston/liner/seal tables; source version only; 6; source catalogue part or assembly drawing identifier | S1, PDF p. 25 |
414-123-09 В | Clamp assembly | Piston assembly 412-126-000; catalogue piston/liner/seal tables; source version only; 7; source catalogue part or assembly drawing identifier | S1, PDF p. 25 |
8Т310.100.115-04 | Seal, D100–160 | Piston assembly 412-126-000; catalogue piston/liner/seal tables; source version only; Table 2 D100–160; source catalogue part or assembly drawing identifier | S1, PDF p. 25 |
412-126-002 | Cylinder liner, D100 | Piston assembly 412-126-000; catalogue piston/liner/seal tables; source version only; Table 3 D100; source catalogue part or assembly drawing identifier | S1, PDF p. 25 |
412-126-100 | Piston assembly, D190 | Piston assembly 412-126-000; catalogue piston/liner/seal tables; source version only; Table 4 D190; source catalogue part or assembly drawing identifier | S1, PDF p. 25 |
412-126-200 | Piston assembly, D160 | Piston assembly 412-126-000; catalogue piston/liner/seal tables; source version only; Table 4 D160; source catalogue part or assembly drawing identifier | S1, PDF p. 25 |
412-126-300 | Piston assembly, D125 | Piston assembly 412-126-000; catalogue piston/liner/seal tables; source version only; Table 4 D125; source catalogue part or assembly drawing identifier | S1, PDF p. 25 |
239TBB045A | Piston assembly, 4½ inches (114.3 mm) | Piston assembly 412-126-000; catalogue piston/liner/seal tables; source version only; Table 4 D4½ inches; alphanumeric piston identifier printed in this source catalogue; manufacturer provenance not independently established | S1, PDF p. 25 |
241TBB045A | Piston assembly, 5 inches (127 mm) | Piston assembly 412-126-000; catalogue piston/liner/seal tables; source version only; Table 4 D5 inches; alphanumeric piston identifier printed in this source catalogue; manufacturer provenance not independently established | S1, PDF p. 25 |
243TBB045A | Piston assembly, 5½ inches (139.7 mm) | Piston assembly 412-126-000; catalogue piston/liner/seal tables; source version only; Table 4 D5½ inches; alphanumeric piston identifier printed in this source catalogue; manufacturer provenance not independently established | S1, PDF p. 25 |
245TBL045A | Piston assembly, 6 inches (152.4 mm) | Piston assembly 412-126-000; catalogue piston/liner/seal tables; source version only; Table 4 D6 inches; alphanumeric piston identifier printed in this source catalogue; manufacturer provenance not independently established | S1, PDF p. 25 |
202TBL045A | Piston assembly, 6½ inches (165.1 mm) | Piston assembly 412-126-000; catalogue piston/liner/seal tables; source version only; Table 4 D6½ inches; alphanumeric piston identifier printed in this source catalogue; manufacturer provenance not independently established | S1, PDF p. 25 |
412-127-100 | Tank | Piston-wash system 412-127-000; catalogue Figure 8 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 27 |
412-127-200 | Screen | Piston-wash system 412-127-000; catalogue Figure 8 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 27 |
412-127-300 | Guard | Piston-wash system 412-127-000; catalogue Figure 8 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 27 |
412-127-400 | Cover | Piston-wash system 412-127-000; catalogue Figure 8 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 27 |
412-117-002-В-ВМ | Manifold | Piston-wash system 412-127-000; catalogue Figure 8 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 27 |
412-117-014-Д-ВМ | Pipe connection | Piston-wash system 412-127-000; catalogue Figure 8 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 27 |
412-117-014-Д-ВМ-01 | Pipe connection | Piston-wash system 412-127-000; catalogue Figure 8 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 27 |
412-127-001 | Connector | Piston-wash system 412-127-000; catalogue Figure 8 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 27 |
412-127-002 | Hose 20×29-1.6 | Piston-wash system 412-127-000; catalogue Figure 8 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 27 |
412-127-003 | Hose 38×49-1.6 | Piston-wash system 412-127-000; catalogue Figure 8 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 27 |
412-127-004 | Hose 38×49-1.6 | Piston-wash system 412-127-000; catalogue Figure 8 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 27 |
412-117-001Е/1-ВМ | Gasket | Piston-wash system 412-127-000; catalogue Figure 8 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 27 |
412-117-001Е/1-ВМ-01 | Gasket | Piston-wash system 412-127-000; catalogue Figure 8 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 27 |
412-117-001Е/2-ВМ | Nipple | Piston-wash system 412-127-000; catalogue Figure 8 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 27 |
412-117-001Е/3-ВМ | Nipple | Piston-wash system 412-127-000; catalogue Figure 8 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 27 |
412-117-001Е/4-ВМ | Clamp | Piston-wash system 412-127-000; catalogue Figure 8 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 27 |
412-117-001Е/4-ВМ-01 | Clamp | Piston-wash system 412-127-000; catalogue Figure 8 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 27 |
412-117-001Е/5-ВМ | Pipe nipple | Piston-wash system 412-127-000; catalogue Figure 8 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 27 |
412-116-009-ВМ-01 | Connector | Piston-wash system 412-127-000; catalogue Figure 8 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 27 |
412-117-001Е/6-ВМ | Nipple | Piston-wash system 412-127-000; catalogue Figure 8 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 27 |
412-116-201-ВМ-02 | Nut | Piston-wash system 412-127-000; catalogue Figure 8 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 27 |
8Т310.130.122 | Seal | Piston-wash system 412-127-000; catalogue Figure 8 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 27 |
412-119-001-ВМ | Gasket | Piston-wash system 412-127-000; catalogue Figure 8 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 27 |
412-119-002-ВМ | Nut | Piston-wash system 412-127-000; catalogue Figure 8 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 27 |
6Р13.8.59 | Voltage warning sign | Piston-wash system 412-127-000; catalogue Figure 8 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 27 |
412-127-006 | Bolt | Piston-wash system 412-127-000; catalogue Figure 8 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 27 |
8Т310.300.011 | Cap | Piston-wash system 412-127-000; catalogue Figure 8 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 27 |
412-127-400-01 | Cover | Piston-wash system 412-127-000; catalogue Figure 8 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 27 |
412-127-008 | Tubular electric heater | Piston-wash system 412-127-000; catalogue Figure 8 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 27 |
8Т650ВМ.700.100 | Housing | High-pressure pulsation dampener 8Т650ВМ.700.000; catalogue Figure 9 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 30 |
8Т650ВМ.700.200 | Punch assembly | High-pressure pulsation dampener 8Т650ВМ.700.000; catalogue Figure 9 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 30 |
8Т650ВМ.700.300 | Diaphragm | High-pressure pulsation dampener 8Т650ВМ.700.000; catalogue Figure 9 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 30 |
8Т650ВМ.600.100 | Shutoff valve | High-pressure pulsation dampener 8Т650ВМ.700.000; catalogue Figure 9 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 30 |
8Т650ВМ.700.001 | Cover | High-pressure pulsation dampener 8Т650ВМ.700.000; catalogue Figure 9 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 30 |
8Т650ВМ.700.002 | Seat | High-pressure pulsation dampener 8Т650ВМ.700.000; catalogue Figure 9 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 30 |
8Т650ВМ.700.009 | Cap | High-pressure pulsation dampener 8Т650ВМ.700.000; catalogue Figure 9 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 30 |
8Т650ВМ.700.010 | Nameplate | High-pressure pulsation dampener 8Т650ВМ.700.000; catalogue Figure 9 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 30 |
8Т650ВМ.700.011 | Washer | High-pressure pulsation dampener 8Т650ВМ.700.000; catalogue Figure 9 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 30 |
8Т650ВМ.700.012 | Membrane | High-pressure pulsation dampener 8Т650ВМ.700.000; catalogue Figure 9 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 30 |
8Т650ВМ.700.013 | Bushing | High-pressure pulsation dampener 8Т650ВМ.700.000; catalogue Figure 9 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 30 |
8Т650ВМ.700.014 | Screw | High-pressure pulsation dampener 8Т650ВМ.700.000; catalogue Figure 9 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 30 |
8Т650ВМ.600.300 | Housing for 8Т650ВМ.600.000 | Low-pressure pulsation dampener 8Т650ВМ.600.000 or 8Т650ВМ.600.000-01; catalogue Figure 10 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 32 |
8Т650ВМ.600.300-01 | Housing for 8Т650ВМ.600.000-01 | Low-pressure pulsation dampener 8Т650ВМ.600.000 or 8Т650ВМ.600.000-01; catalogue Figure 10 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 32 |
8Т650ВМ.400.100 | Piston | Safety valve 8Т650ВМ.400.000 or 8Т650ВМ.400.000-01; catalogue Figure 11 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 34 |
8Т650ВМ.400.200 | Guard | Safety valve 8Т650ВМ.400.000 or 8Т650ВМ.400.000-01; catalogue Figure 11 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 34 |
8Т650ВМ.400.001 | Housing for 8Т650ВМ.400.000 | Safety valve 8Т650ВМ.400.000 or 8Т650ВМ.400.000-01; catalogue Figure 11 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 34 |
8Т650ВМ.400.001-01 | Housing for 8Т650ВМ.400.000-01 | Safety valve 8Т650ВМ.400.000 or 8Т650ВМ.400.000-01; catalogue Figure 11 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 34 |
8Т650ВМ.400.010 | Adapter | Safety valve 8Т650ВМ.400.000 or 8Т650ВМ.400.000-01; catalogue Figure 11 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 34 |
8Т650ВМ.400.016 | Knife for 8Т650ВМ.400.000 | Safety valve 8Т650ВМ.400.000 or 8Т650ВМ.400.000-01; catalogue Figure 11 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 34 |
8Т650ВМ.400.019 | Knife for 8Т650ВМ.400.000-01 | Safety valve 8Т650ВМ.400.000 or 8Т650ВМ.400.000-01; catalogue Figure 11 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 34 |
8Т650ВМ.400.004 | Bushing | Safety valve 8Т650ВМ.400.000 or 8Т650ВМ.400.000-01; catalogue Figure 11 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 34 |
8Т650ВМ.400.005 | Rod | Safety valve 8Т650ВМ.400.000 or 8Т650ВМ.400.000-01; catalogue Figure 11 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 34 |
8Т650ВМ.400.006 | Shaft | Safety valve 8Т650ВМ.400.000 or 8Т650ВМ.400.000-01; catalogue Figure 11 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 34 |
8Т650ВМ.400.021 | Plate for 8Т650ВМ.400.000 | Safety valve 8Т650ВМ.400.000 or 8Т650ВМ.400.000-01; catalogue Figure 11 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 34 |
8Т650ВМ.400.018 | Plate for 8Т650ВМ.400.000-01 | Safety valve 8Т650ВМ.400.000 or 8Т650ВМ.400.000-01; catalogue Figure 11 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 34 |
8Т650ВМ.400.008 | Damper | Safety valve 8Т650ВМ.400.000 or 8Т650ВМ.400.000-01; catalogue Figure 11 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 34 |
8Т650ВМ.400.009 | Pivot pin | Safety valve 8Т650ВМ.400.000 or 8Т650ВМ.400.000-01; catalogue Figure 11 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 34 |
8Т650ВМ.400.023 | Nameplate for 8Т650ВМ.400.000 | Safety valve 8Т650ВМ.400.000 or 8Т650ВМ.400.000-01; catalogue Figure 11 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 34 |
8Т650ВМ.400.023-01 | Nameplate for 8Т650ВМ.400.000-01 | Safety valve 8Т650ВМ.400.000 or 8Т650ВМ.400.000-01; catalogue Figure 11 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 34 |
8Т650ВМ.010.004 | Union nut | Safety valve 8Т650ВМ.400.000 or 8Т650ВМ.400.000-01; catalogue Figure 11 / BOM; source catalogue part or assembly drawing identifier | S1, PDF p. 34 |
412-128-000 | Crankcase steam pipe | Lubrication system 412-118-000; catalogue BOM continuation; starred items not shown in Figure 5; source catalogue part or assembly drawing identifier | S1, PDF p. 16 |
412-129-003 | Tubular electric heater | Lubrication system 412-118-000; catalogue BOM continuation; starred items not shown in Figure 5; source catalogue part or assembly drawing identifier | S1, PDF p. 16 |
412-126-002 | Cylinder liner, D100 mm | Table A.1; D100 mm, mass 84.5 kg; source catalogue part or assembly drawing identifier | S2, PDF p. 57 |
412-126-100 | Piston assembly, D190 mm | Table A.2; D190 mm, mass 11.1 kg; source catalogue part or assembly drawing identifier | S2, PDF p. 57 |
412-126-200 | Piston assembly, D160 mm | Table A.2; D160 mm, mass 8.47 kg; source catalogue part or assembly drawing identifier | S2, PDF p. 57 |
412-126-300 | Piston assembly, D125 mm | Table A.2; D125 mm, mass 4.81 kg; source catalogue part or assembly drawing identifier | S2, PDF p. 57 |
8Т310.100.115-02 | Seal for cylinder liner D100 mm | Table A.3; liner bore D100 mm; mass 0.020 kg; this manual version only. Catalogue page 25 has a different seal-to-bore table.; source catalogue part or assembly drawing identifier | S2, PDF p. 57 |
8Т310.100.115-03 | Seal for cylinder liner D110 / 125 mm | Table A.3; liner bore D110 / 125 mm; mass 0.024 kg; this manual version only. Catalogue page 25 has a different seal-to-bore table.; source catalogue part or assembly drawing identifier | S2, PDF p. 57 |
8Т310.100.115-04 | Seal for cylinder liner D140 / 150 / 160 mm | Table A.3; liner bore D140 / 150 / 160 mm; mass 0.029 kg; this manual version only. Catalogue page 25 has a different seal-to-bore table.; source catalogue part or assembly drawing identifier | S2, PDF p. 57 |
8Т310.100.115-05 | Seal for cylinder liner D170 / 180 mm | Table A.3; liner bore D170 / 180 mm; mass 0.031 kg. The next bore cell is blank in this scan; no D190 assignment inferred. This manual version only; catalogue PDF25 differs.; source catalogue part or assembly drawing identifier | S2, PDF p. 57 |
412-126-300 | Piston assembly | Appendix A, figure A.8; source catalogue part or assembly drawing identifier | S2, PDF p. 58 |
412-126-200 | Piston assembly | Appendix A, figure A.9; source catalogue part or assembly drawing identifier | S2, PDF p. 59 |
412-126-100 | Piston assembly | Appendix A, figure A.10; source catalogue part or assembly drawing identifier | S2, PDF p. 60 |
412-126-002 | Cylinder liner, D100 mm | Figure A.22, base row D100 mm, mass 84.5 kg; source catalogue part or assembly drawing identifier | S2, PDF p. 74 |
414-123-302-ВМ | Piston core, D100 mm | Figure A.23; D100 mm, mass 1.6 kg; source catalogue part or assembly drawing identifier | S2, PDF p. 75 |
414-123-111ВМ | Piston core, diameter 150 mm | Figure A.24; outer diameter 150 mm, mass 3.8 kg; source prints no hyphen before ВМ; source catalogue part or assembly drawing identifier | S2, PDF p. 76 |
414-123-111ВМ-01 | Piston core, diameter 160 mm | Figure A.24; outer diameter 160 mm, mass 4.2 kg; source prints no hyphen before ВМ; source catalogue part or assembly drawing identifier | S2, PDF p. 76 |
414-123-111ВМ-02 | Piston core, diameter 170 mm | Figure A.24; outer diameter 170 mm, mass 4.7 kg; source prints no hyphen before ВМ; source catalogue part or assembly drawing identifier | S2, PDF p. 76 |
414-123-111ВМ-03 | Piston core, diameter 180 mm | Figure A.24; outer diameter 180 mm, mass 5.2 kg; source prints no hyphen before ВМ; source catalogue part or assembly drawing identifier | S2, PDF p. 76 |
414-123-111ВМ-04 | Piston core, diameter 190 mm | Figure A.24; outer diameter 190 mm, mass 5.8 kg; source prints no hyphen before ВМ; source catalogue part or assembly drawing identifier | S2, PDF p. 76 |
412-126-110 | Piston cup | Figure A.25; source D=189.8 mm, mass 3.39 kg; source catalogue part or assembly drawing identifier | S2, PDF p. 77 |
412-126-210 | Piston cup | Figure A.26; source D=159.8 mm, mass 2.57 kg; source catalogue part or assembly drawing identifier | S2, PDF p. 78 |
412-126-310 | Piston cup | Figure A.27; source D=124.8 mm, mass 1.01 kg; source catalogue part or assembly drawing identifier | S2, PDF p. 79 |
8Т310.100.115 | Seal, D89 mm | Figure A.30; source dimension D89 ±1 mm, mass 0.013 kg; base code only; source catalogue part or assembly drawing identifier | S2, PDF p. 82 |
412-114-004-С | Lower crosshead guide | Figure A.33 sheet 2; full identifier printed at top; paired drawing sheet 1 on PDF85; source catalogue part or assembly drawing identifier | S2, PDF p. 86 |
412-114-003-С | Upper crosshead guide | Figure A.34 sheet 2; full identifier printed at top; paired drawing sheet 1 on PDF87; source catalogue part or assembly drawing identifier | S2, PDF p. 88 |
413-000-001 | Company nameplate | Appendix B nonferrous materials table; not an operating or delivery specification; source catalogue part or assembly drawing identifier | S2, PDF p. 95 |
Reference documents and scope
- S1 — 8T-650-01 parts and assembly catalogue, 413-000-000 КДС. Reference file: 8Т-650-01 (ред.).pdf.
- S2 — 8T-650-01 operating manual, 2003, 8Т-650-01 РЭ. Reference file: 8Т-650-01РЭ.pdf.
PDF page numbers count from the first page of each reference file. Brand names identify the equipment or catalogue source. A listed number does not establish interchangeability, original-manufacturer authorisation, stock or a delivery commitment. Send the nameplate, complete reference, quantity and drawing revision for a parts review.
Send a 8T-650-01 parts request
Include the full part number, quantity, nameplate photograph and drawing revision. Matching and availability require review of your actual equipment.